Effects of different metal corrosion inhibitors on hydrogen suppression and film formation with Mg–Zn alloy dust in NaCl solutions

To improve the safety of wet dust removal systems for processing magnesium-based alloys, a new method is proposed for preventing hydrogen generation. In this paper, hydrogen generation by Mg–Zn alloy dust was inhibited with six common metal corrosion inhibitors. The results showed that sodium dodecylbenzene sulfonate was the best hydrogen inhibitor, while CeCl₃ enhanced hydrogen precipitation. The film-forming stability of sodium dodecylbenzene sulfonate was tested with different contents, temperatures, Cl^? concentrations and perturbation rates. The results showed that this inhibitor formed stable protective films on the surfaces of Mg–Zn alloy particles, and adsorption followed the Langmuir adsorption model.     

Hydrogeochemical Processes and Inverse Modeling for a Multilayer Aquifer System in the Yuaner Coal Mine,Huaibei Coalfield,China

Coal mining can dramatically change hydrogeological conditions and induce serious environmental problems. Fifty groundwater samples were collected from the main aquifers in the Yuaner coal mine (Anhui Province, China). The results show that the main hydrogeochemical processes in the mine include dissolution, precipitation, pyrite oxidation, desulfurization, and cation exchange. The Neogene porous aquifer is affected by groundwater flow conditions; its main hydrogeochemical processes are dissolution of carbonate minerals and gypsum, and cation exchange. The Permian coal measure’s fractured sandstone aquifer was confirmed to be controlled by the region’s geological structure; its main hydrogeochemical processes are desulfurization and cation exchange. The Carboniferous Taiyuan limestone aquifer was determined by both groundwater flow conditions and regional geological structure; its main hydrogeochemical processes are dissolution of carbonate minerals and gypsum, pyrite oxidation, and cation exchange. Additionally, hydrogeochemical inverse modeling of the groundwater flow path confirm the hydrochemistry results and principal component analysis.

     

Rapid preparation of Palygorskite/Al2O3 composite aerogels with superhydrophobicity,high-temperature thermal insulation and improved mechanical properties

Al₂O₃ aerogels are widely employed in heat insulation and flame retardancy because of their unique combination of low thermal conductivity and exceptional high-temperature stability. However, the mechanical properties of Al₂O₃ aerogel are poor, and the preparation time is considerably long. In this study, we present a simple and scalable approach to construct monolithic Pal/Al₂O₃ composite aerogels using solvothermal treatment instead of traditional solvent replacement, which remarkably shortened the preparation time. Subsequently, to obtain stable superhydrophobicity (θ > 152°), the Pal/Al₂O₃ aerogel was modified by gas-phase modification method. The obtained Pal/Al₂O₃ composite aerogels demonstrate the integrated properties of low density (0.078–0.106 g/cm³), low thermal conductivity (1000 °C, 0.143 W/(m·K)), good mechanical properties (Young's modulus, 1.6 MPa), and good heat resistance. The monolithic Pal/Al₂O₃ composite aerogels with improved mechanical performance and improved thermal stability can show great potential in the field of thermal insulation.     

Microbial coupled photocatalytic fuel cell with a double Z-scheme g-C3N4/ZnO/Bi4O5Br2 cathode for the degradation of different organic pollutants

A novel heterostructure of g-C₃N₄/ZnO/Bi₄O₅Br₂ (ZB-3) was designed, and used in the microbial coupled photocatalytic fuel cell (MPFC). It can effectively improve electron utilization efficiency and pollutant degradation using this double Z-scheme heterojunction structure. The current–time (I–t) curves demonstrated that the current density of ZB-3 was higher than that of ZnO, ZnO/Bi₄O₅Br₂ (ZB-1), g-C₃N₄/ZnO (ZB-2). Electrochemical impedance spectroscopy (EIS) indicated ZB-3 possessed the minimum charge-transfer resistance. This MPFC for degrading rhodamine B (RhB) and tetracycline (TC) under different conditions were developed using these materials. Even in the dark condition, MPFC with g-C₃N₄/ZnO/Bi₄O₅Br₂ demonstrated 93% and 82% degradation efficiency for RhB and TC, respectively. Furthermore, the electron transport mechanism of the MPFC and ZB-3 were proposed. It paves the approach for more efficient pollutant degradation via MFC photocatalysis.     

羟肟酸类捕收剂浮选金红石特性及其机理

浮选药剂的研究是金红石浮选技术发展的重要方向。通过单矿物浮选试验、扫描电镜、红外光谱分析、接触角测试及吸附量测试，研究了苯甲羟肟酸、水杨羟肟酸、辛基异羟肟酸对金红石浮选行为的影响以及三种羟肟酸在金红石表面的吸附机理。结果表明:苯甲羟肟酸、水杨羟肟酸、辛基异羟肟酸在pH值分别为6.5、6.5、5.5左右时，对金红石纯矿物具有较好的捕收性能。金红石与三种羟肟酸均发生化学吸附，但苯甲羟肟酸捕收性能最好，回收率达到82%。      

Flame characteristics of premixed H2-air mixtures explosion venting in a spherical container through a duct

The explosion venting duct can effectively reduce the hazard degree of a gas explosion and conduct the venting energy to the safe area. To investigate the flame quantitative propagation law of explosion venting with a duct, the effects of hydrogen fraction and explosion venting duct length on jet flame propagation characteristics of premixed H₂-air mixtures were analyzed through experiment and simulation. The experiment results under initial conditions of room temperature and 1 atm show that when hydrogen fraction was high enough, part of the unburned hydrogen was mixed with air again to reach an ignitable concentration, resulting in the secondary combustion was easier produced and the duration of the secondary flame increased. With the increase of venting duct length, the flame front distance and propagation velocity increased. Meanwhile, the spatial distribution of pressure field and temperature field, and the propagation process and mechanism of the flame venting with a duct were analyzed using FLUENT software. The variation of the pressure wave and the pressure reflection oscillation law in the explosion venting duct was captured. Therefore, in the industrial explosion venting design with a duct, the hazard caused by the coupling of venting pressure and venting flame under different fractions should be considered comprehensively.     

Improvement in the properties of low carbon MgO-C refractories through the addition of graphite-SiC micro-composite

Graphite–SiC micro-composites have been prepared in–house by carbothermal reduction process. Controlling the process parameters including the weight ratio of SiO₂ to graphite as well as carbothermal reduction temperature during the micro-composite preparation favors the homogeneous formation of SiC with preferred morphologies like ribbons and whiskers/fibers. The micro-composite modified low carbon MgO-C refractories have exhibited significantly improved bulk properties over the standard composition. To understand the beneficial role of SiC reinforcement on hot strength performance under air oxidizing conditions, we propose a scaling parameter known as strength factor (fs) based on the ratio of hot strength (HMOR) to cold strength (CCS). Correlating the strength factor data (fs) with oxidative damage provides new insights into the reinforcing effects of distinct SiC morphologies in this new class of micro-composite fortified refractory systems over the standard compositions.     

Users’ Preferences for Smart Home Automation – Investigating Aspects of Privacy and Trust

Smart home automation provides residents with relief and convenience in everyday life and allows for self-determined aging in place. Yet, market penetration is offset by user concerns related to privacy and trust issues: With increasing system complexity, users may perceive a loss of control and fear technical unreliability. While barriers to acceptance in terms of privacy and trust are well understood when considered separately, they are hardly investigated in conjunction so far. We conducted a quantitative study using Adaptive Choice-Based Conjoint Analysis via an online questionnaire. We explored how aspects of privacy and trust determine the willingness to use smart homes from the perspective of (future) users (n = 137, 18 to 64 years of age), and also with respect to the level of automation and application field. Results show that semi-automated systems are rather preferred than fully automated smart home technology. The perceived reliability of automation is the most important acceptance determinant, followed by the location of data storage. Whereas the awareness to use (e.g., recommendations), the type of data, and application field are less important factors for the overall willingness to use smart homes. Findings inform scientists in the field of human-automation interaction and technical developers of smart home automation for technology innovation adapted to user needs.